home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Ham Radio 2000
/
Ham Radio 2000.iso
/
ham2000
/
mods
/
cellular
/
ft411.mod
< prev
next >
Wrap
Text File
|
1994-01-10
|
5KB
|
127 lines
Subject: ft411 modif's
Date: 6 Feb 89 20:03:02 GMT
copied from packet KD6TH BBS
(Note: I have not tried or verified these mods, proceed at your own risk!)
From: 4X6TL@4Z4SV
Hello to all the owners of the FT-411 OF YAESU,
I have this Hand held, and by playing with it,
I discovered a nice trick to increase it frequency coverage.
It is so simple that you don't even have to open your hand held.
All you have to do is:
1. Make sure that the power switch is off.
2. press the UP arrow and DOWN arrow together, at the same time
(those keys are also called A, and B.
and they placed at the upper right side of the keyped)
3. Keep pressing both buttons and turn the power on.
That's all.
Now you can receive 130-174Mhz, and transmit 140-150Mhz
CAUTON: When you do this modification the memories can be
erased.
Ayhow I think it is not the end, and there are some more
options.
If you do have some more information about this Hand
held,
Please leave me a msg with it.
Tnx, AVIAD, 4X6TL@4Z4SV
1508z, 635 msgs, #24083
last @KD6TH-4 MailBox>
Date: Thu, 16 Feb 89 14:26:30 EST
Subject: more mods
From: rfc@briar.philips.com (Robert Casey;6282;3.57;$0201)
Subject: FT 411 mods
copied from packet:
Msg# TSP Size Read To @ BBS From Date Time
24250 BN 2876 1 YAESU 4X6TL 890208 1513
Subject: FT-411 Modification.
From: 4X6TL@4Z4SV
Hi everybody.
Here is some new interesting info about the FT-411:
FT 411 OUT OF BAND MODIFICATIONS.
---------------------------------
1) Open the front cover
2) Locate the C.P.U. unit (it is located on the
front cover ).
3) Locate Jumpers 1,2,3 and 4 , These are the
band setting Jumpers
4) Jumpers No 1,2 and 4 should be
disconnected ,and Jumper No 3 should
be connected.
5) Close the radio .
6) Apply power to the radio and turn it
on.
The display will initialize with
memory No 1 flashing and the
frequency display will show
1.000
7) Now , adjust the display to
the desired lowest receive
frequency
When done ,press VFO.
The memory CH will now
show 2 flashing .
8) Adjust the display to the desired highest receive
frequency When done press VFO .
The memory CH will now show 3 flashing .
9) Adjust the display to the desired lowest transmit
frequency
When done ,press VFO.
The memory CH will now show 4 flashing
10)
Now , adjust the display to the desired highest
transmit frequency
When done ,press VFO.
The rig
is now set for your programed band on transmit and receive.
COMMENTS
-------
1)
After the rig was programmed to the band and you want to change it
to
other ranges you will have to open the rig again and disconnect
Jumper No 3 then to apply power to the radio ,turn it on again
open it again ,connect Jumper No 3 back and repeat from steps 5 .
Any
comment and other information would be appreciated.
Good Luck
Aviad 4X6TL@4Z4SV
disclamer: I have not tested or verified the above, proceed at your own risk.
WA2ISE
..........................................................................
. Mark Bramwell, VE3PZR .
. .
. The University of Western Ontario Bitnet: MBRAMWEL@UWO.CA .
. School of Business Administration Packet: VE3PZR @ VE3GYQ .
. London, Ontario, N6A 3K7 Phone: (519) 661-3714 .
..........................................................................